The Fundamentals of Plumbing Skills for Bathtub Installation
The Fundamentals of Plumbing Skills for Bathtub Installation
Blog Article
We've stumbled upon this great article about How to Install a Bathtub Yourself directly below on the internet and decided it made sense to write about it with you on this site.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily accessible, the task can move immediately; if you have to open up a wall surface to remove the old bathtub and place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make sure you have certified yourself for the job and also fit attempting it. Instead of hiring a service provider to take control of a halfway-completed job, it is far better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly help you install a brand-new bathtub in your washroom if you have actually currently acquired a new bathtub and don't need to change the arrangement of your previous water system pipes.
Your tools and material checklist need to comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of removing the existing faucets can be quite bothersome due to the limited accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipelines. Once the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers remain in place between the faucet and also the sink. Secure the tap in position with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the called for placement. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub up until the spirit level reads level.
To set up taps, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if necessary. Load the tub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub should wait till the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, causing difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and also cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about How to Install a Bathtub, I imagined sharing that piece of content was essential. Sharing is good. You won't know, you might be helping someone out. I am grateful for your time. Kindly visit our website back soon.
Customer Reviews Report this page